H35-580_V2.0 Dumps with Practice Exam Questions Answers

According to the Hardware Description: Bbu5900 V100r013c10, these statements are correct about the space principles for 5G BBU installation:

• If the installation space is insufficient, the BBU can be installed on a wall. Ensure that the wall meets the load bearing requirements: The BBU can be installed on a wall using wall-mounted brackets. The wall must be able to bear at least four times the weight of the BBU and must be flat and vertical. The installation height of the BBU must not exceed 2 m.
• If the space is greater than 600 mm, a cabinet can be added to install the BBU: The BBU can be installed in a cabinet that meets the requirements of Huawei base stations. The cabinet must have a width of 19 inches and a depth of at least 600 mm. The cabinet must also provide sufficient ventilation, grounding, and lightning protection for the BBU.
• If the remaining space of an existing cabinet is greater than 4 U, the BBU can be installed directly: The BBU can be installed in an existing cabinet that has enough space for it. The BBU has a height of 2 U, so it requires at least 4 U of space in a cabinet. The existing cabinet must also meet the requirements of Huawei base stations.

The other statement is incorrect about the space principles for 5G BBU installation:

• If the installation space is insufficient, install 5G boards directly into the existing 4G B8U: This statement is not supported by Huawei base stations. The 5G boards cannot be installed directly into the existing 4G B8U because they have different slot distributions and board types. The 5G boards can only be installed in a BBU5900 subrack that supports both LTE and NR modes.

According to the 5G EN-DC Architecture and Interfaces, there are two methods that can be used to support X2 interconnection between an eNodeB and a gNodeB in NSA networking:

• Interconnection through CI interfaces on the UMPT boards in different subracks: The UMPT is a universal main processing and transmission unit that provides main processing and transmission functions for a subrack. The UMPT has two CI interfaces that can be used for X2 interconnection with other base stations. The CI interfaces support CPRI, OBSAI, and eCPRI protocols and can use optical fibers or electrical cables for transmission. The CI interfaces can be configured as master or slave interfaces depending on the network topology.
• IPRAN interconnection between subracks: IPRAN is an IP-based radio access network that uses IP transport technologies to carry base station traffic over Ethernet or MPLS networks. IPRAN can support X2 interconnection betweendifferent base stations by using IP routers or switches. IPRAN can provide flexible networking, high bandwidth, low latency, and high reliability for X2 interconnection.

The other two methods are not valid for X2 interconnection between an eNodeB and a gNodeB:

• Interconnection via backplane in a subrack: This method is only applicable for X2 interconnection between two eNodeBs or two gNodeBs that are installed in the same subrack. The backplane is the internal bus that connects different boards within a subrack. The backplane supports CPRI, OBSAI, and eCPRI protocols and can provide high-speed data transmission between boards.
• Interconnection through HEI interfaces on the UBBP boards in different subracks: This method is not supported by Huawei base stations. The HEI interface is a high-speed Ethernet interface that is used for data transmission between base stations and core networks or transport networks. The HEI interface supports S1, Xn, F1, E1, and N2 protocols and can use optical fibers or electrical cables for transmission. The HEI interface cannot be used for X2 interconnection between base stations.

Therefore, the correct answer is A and D.

According to the Huawei’s Latest AAU Products, Huawei’s AAUs have an operating voltage of -48 V DC and support LTE-NR dual-mode on some frequency bands, such as C-band and sub-3 GHz bands. The article also states that Huawei’s new-generation 64T64R AAUs provide higher coverage gains than conventional 32T32R AAUs by using ELAA (extremely large antenna array) technology. Huawei’s AAUs do not support GSM-NR dual-mode on any frequency band, as GSM is not a compatible RAT with NR.

According to the HCIA-5G V2.0 Exam Outline, no response from the UE, insufficient radio resources, and unauthorized UE are cause values of QoS flow setup failures, which correspond to options A, B, and D. Insufficient transmission resources is not a cause value of QoS flow setup failures, but a cause value of handover execution failures, which corresponds to option C.

According to the HCIA-5G V2.0 Exam Outline, the 3.5 GHz+2.1 GHz uplink and downlink decoupling/super uplink architecture uses spectrum sharing technologies such as Dynamic Spectrum Sharing (DSS) and Spectrum Sharing (SS) to enable 3.5 GHz NR and 2.1 GHz LTE to share only the uplink spectrums, while the downlink spectrums are used exclusively by each technology.